To have various IP ranges in the same subnet and assign the IP Address depending of the device type that sends the request.

[Juan Antonio García Moreno]

Sten, a lot of thanks...

Do you have some examples that you can share with me to assign a range or
other depending of the device type that send the request to begin to work
over that?


Best regards,

Juan García

El jue., 1 ago. 2019 a las 13:06, Sten Carlsen (<stenc at s-carlsen.dk>)
escribió:

>
>
> On 01/08/2019 09.05, Juan Antonio García Moreno wrote:
>
> Hi everyone,
>
> I have read a lot of information on Internet but I haven't this too clear
> and I would like ask you if this can do or not.
>
> This is the situation:
>
> - I have a network wired and WIFI.
> - I have the ISC DHCP Server that assign IP address statically with
> "fixed-address" and dinamically from a pool address with "range".
>
> I would know if I can to have, for example, 3 ranges and assign the IP
> Address depending of the device type that request the IP.
>
> For example:
>
> - Static IP to devices that I want by MAC.
> - POOL1 to LAPTOP.
> - POOL2 to Smartphones.
> - POOL3 to Tablets or Watches.
>
> How could I discriminate the request and assign the IP from POOL1, POOL2
> or POOL3 depending if the device is a LAPTOP, a Smartphone or a Tablet?
>
> Can I do this?
>
> What I do is the following:
>
>    - I have a few static host entries defined globally for a few hosts
>    that need a fixed address
>    - I have one subnet for unknown devices - devices that are connected
>    but have not been accepted by me
>    - I have a different subnet for normal use
>       - I have one pool for devices that are allowed internet access
>       - I have one pool for devices that are not allowed internet access
>       - I have a space for the fixed addresses outside of these pools
>    - I have defined two classes, one for internet access and one without
>       - I use a list of subclass definitions for every device without a
>       fixed address
>       - each subclass definition determines access or not by assigning to
>       the class and in some cases give the DNS name
>    - Each pool definition use deny and allow statements to allow only the
>    relevant devices
>
> The difficult part of your setup will be to assign each device to the
> correct class. There are lots of possibilities but specific knowledge is
> needed about your devices to do that.
>
> I use a manually edited list of subclass definitions because this fits my
> needs. My next setup will be KEA with mysql backend and a web page to do
> the administration.
>
>
> What would be the best way to do it?
>
> Does anyone have, and can show me, some examples?
>
>
> Best regards,
>
> Juan García
>
> _______________________________________________
> dhcp-users mailing listdhcp-users at lists.isc.orghttps://lists.isc.org/mailman/listinfo/dhcp-users
>
>
>

-- 
[image: EMERGYA] <http://www.emergya.com/>
*Juan García*

*Dto. de Soporte Interno*

*EMERGYA INGENIERÍA*

*m:* +34 954 517 577

*p:* +34 954 517 577
*e:* jagarcia at emergya.com
[image: linkedin icon] <https://www.linkedin.com/company/emergya>  [image:
facebook icon] <https://www.facebook.com/Emergya>  [image: twitter icon]
<https://twitter.com/emergya>  [image: youtube icon]
<https://www.youtube.com/channel/UCU0ISPwk1pcOWwjpX63gN_A>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://lists.isc.org/pipermail/dhcp-users/attachments/20190801/efee3e12/attachment-0001.html>